Features & Benefits
  • Broadband performance DC to 18 GHz with low reflection stainless steel construction and ¼ – 36 threaded coupling offers high performance in a compact design.
  • Low cost Commercial Grade (Brass SMA) available in nickel or gold plating which provides approximately 30% cost reduction with 250 mating cycles.
  • Available for .085″ and .141″ diameter semi-rigid cables and all the standard flexible cables including double shielded RG-316.
  • Phase Adjustable SMA connectors provide ease of mechanical screw adjustments, compared to the delays and expense of laborious cable-trimming.

How to buy this Product

Buy Now

 

 

RFC100A – LMR100A – RG316 – RG174 2D Drawing
SMA Male for RG316 / RG174A-U / LMR100A / RFC100A
SMA Male Right Angle for RG316 / RG174A-U / LMR100A / RFC100A
Reverse Polarity SMA Male for RG316 / RG174A-U / LMR100A / RFC100A
Reverse Polarity SMA Male Right Angle for RG316 / RG174A-U / LMR100A / RFC100A
SMA Female for RG316 / RG174A-U / LMR100A / RFC100A
SMA Female Bulkhead for RG316 / RG174A-U / LMR100A / RFC100A
Reverse Polarity SMA Female Bulkhead for RG316 / RG174A-U / LMR100A / RFC100A
SMA Female Bulkhead Long 14.5MM for RG316 / RG174A-U / LMR100A / RFC100A

 

RFC195 – LMR195 – RG58 – RG142 – RG400 2D Drawing
SMA Male for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
SMA Male Right Angle for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
Reverse Polarity SMA Male for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
Reverse Polarity SMA Male Right Angle for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
SMA Female for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
SMA Female Bulkhead for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
SMA Female Long (Not Bulkhead) for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
Reverse Polarity SMA Female Bulkhead for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
SMA Male (Nickel) for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
Reverse Polarity SMA Male (Nickel) for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223
SMA Female (Nickel) for RG58 / LMR195 / RFC195 / RG142 / RG400 / RG223

 

RFC240 – LMR240 – RG8X 2D Drawing
SMA Male for RG8x / LMR240 / RFC240
SMA Male Right Angle for RG8x / LMR240 / RFC240
Reverse Polarity SMA Male for RG8x / LMR240 / RFC240
Reverse Polarity  SMA Male Right Angle for RG8x / LMR240 / RFC240
SMA Male Captivated (Nickel) for RG8x / LMR240 / RFC240
SMA Female (Nickel) (Not Bulkhead) for RG8x / LMR240 / RFC240
SMA Female Bulkhead for RG8x / LMR240 / RFC240
Reverse Polarity SMA Female Bulkhead for RG8x / LMR240 / RFC240

 

RFC400 – LMR400 – RG213 – RG8U 2D Drawing
SMA Male for LMR400 / RFC400 / RG213 / RG8U
Reverse Polarity SMA Male for LMR400 / RFC400 / RG213 / RG8U
SMA Female Bulkhead for LMR400 / RFC400 / RG213 / RG8U
Reverse Polarity SMA Female Bulkhead for LMR400 / RFC400 / RG213 / RG8U

 

Corrugated Cables 2D Drawing
SMA Male for 1/4 SuperFlex

 

1mm Cable 2D Drawing
SMA Female Bulkhead Long 14.5MM Solder Type for 1mm cable
SMA Female Bulkhead Thin Hex Solder Type for 1mm cable
SMA Female Bulkhead Hex Ring Long 14.5MM Solder Type for 1mm cable

 

RG178 2D Drawing
SMA Female Bulkhead Solder Type for RG 178
Reverse Polarity SMA Female Bulkhead Solder Type for RG 178

 

RG402 2D Drawing
SMA Male for RG402
SMA Male Right Angle for RG402

 

  • Base Stations
  • Instrumentation
  • Process Controls
  • Cable Assemblies
  • Mil/Aero
  • Telecom
  • Components
  • PC/LAN

 

Electrical
Impedance 50 Ω
Frequency Range .141″ & .085″ semi-rigid cable: 0-18 GHz
Flexible cables: 0-12.4 GHz
Voltage Rating RG-55, 58, 141, 142, 223, 303: 500 volts peak
RG-122, 174, 188, 316: 375 volts peak
Dielectric Withstanding Voltage .141″ & RG-58 Cables: 1,000 VRMS
.085″ & RG-316 Cables: 750 VRMS
VSWR Straight connector, .141″: 1.05 + .005 f (GHz)
Straight connector, .RG-55: 1.15 + .011 f (GHz)
Straight connector, RG-122: 1.15 + .02 f (GHz)
Straight connector, RG-178: 1.20 + .025 f (GHz)
Right angle connector, .141″: 1.10 + .01 f (GHz)
Right angle connector, .RG-55: 1.15 + .02 f (GHz)
Right angle connector, RG-122: 1.15 + .03 f (GHz)
Right angle connector, RG-178: 1.20 + .03 f (GHz)
Contact Resistance Center contact: 2.0 mΩ
Body: 2.0 mΩ
Braid to body: 0.5 mΩ
Insulation Resistance 5,000 MΩ minimum
Insertion Loss dB maximum = .03√[f(GHz)]
RF Leakage -60 dB minimum
Mechanical
Mating .250-36 threaded coupling
Mating Torque Minimum: 2 inch pounds (22 N.cm)
Recommended: 7-10 inch pounds (80-110 N.cm)
Maximum: 15 inch pounds (170 N.cm)
Coupling Nut Retention Axial force: 100 inch pounds min. (300 N.cm)
Torque: 15 inch pounds. min. (76 N.cm)
Jacks: N/A
Connector Affixment to Cable Crimp and solder types
Cable Affixment to Center Contact Solder, except as noted
Contact Captivation All types unless noted otherwise
Cable Retention (Crimp) RG-58, 303 and .141″: 60 lbs. minimum
RG-55, 142, & 223: 80 lbs. minimum
Connector Durability 500 mating and unmating cycles @ 12 cycles per minute
Material
Bodies, Coupling Nuts, Other Metal Parts (except as noted) Non-magnetic stainless steel style per QQ-S-764, Type 303
Contacts Beryllium copper per QQ-C-530, heat treated per MIL-H-7199
Center Contact Plating .00005″ minimum gold per MIL-G-45204, type 1, grade C. Gold over nickel unless otherwise requested.
Plating (Other Metal Parts) Gold plated or passivated to meet the finish and corrosion requirements of MIL-C-39012
Insulator TFE fluorocarbon per ASTM D1457
Gaskets Silicone rubber, per MIL-R-5847 and ZZ-R-765 class IIB, grade 65-75.
Lock washers Stainless steel, internal tooth supplied with all bulkhead mounted connectors
Crimp Ferrule Seamless copper tubing alloy #122 (DHP), hard drawn to Rockwell 58-77 on 30-T scale per ASTM B75
Environmental
Temperature Range – 65°C to +165°C
Thermal Shock MIL-STD-202 method 107 (test condition B) except high temperatures @ + 200°C
Vibration MIL-STD-202 method 204 (test condition D)
Shock MIL-STD-202 method 213 (test condition I). No discontinuity permitted.
Corrosion MIL-STD-202 method 101 (test condition B) 5% salt solution
Moisture Resistance MIL-STD-202 method 106, except step 7b (vibration) omitted, and high humidity measurements do not apply
Weatherproofing Crimp type: heat shrink tubing
Solder type: silicone rubber gaskets
Altitude MIL-STD-202 method 105 (test condition C), no corona at 70,000 feet.
.141″ & RG-55: 250 VRMS
.085″ & RG-122: 190 VRMS
Military Specifications
MIL-C-39012 & MIL-C-83517 SMA Specification Sheets As applicable

Note: These characteristics are typical but may not apply to all connectors.

 

Electrical
Impedance 50 Ω
Frequency Range .141″ & .085″ semi-rigid cable: 0-18 GHz
Flexible cables: 0-12.4 GHz
Voltage Rating RG-58, 141, 142: 500 volts peak
RG-174, 188, 316: 375 volts peak
Dielectric Withstanding Voltage .141″ & RG-58 Cables: 1,000 VRMS
.085″ & RG-316 Cables: 750 VRMS
VSWR Straight connector, .141″: 1.05 + .005 f (GHz)
Straight connector, .RG-174: 1.15 + .02 f (GHz)
Straight connector, RG-58: 1.15 + .01 f (GHz)
Straight connector, RG-178: 1.20 + .025 f (GHz)
Contact Resistance Center contact: 2.0 mΩ
Body: 2.0 mΩ
Braid to body: 0.5 mΩ
Insulation Resistance 5,000 MΩ
Insertion Loss dB maximum = .06v[f(GHz)] Test frequency @ 6.0 GHZ
RF Leakage -90 dB minimum @ 2.3 GHz
Mechanical
Mating .250-36 threaded coupling
Mating Torque Minimum: 2 inch pounds (12 N.cm)
Recommended: 7-10 inch pounds (80-110 N.cm)
Maximum: 15 inch pounds (170 N.cm)
Connector Durability 100 matings
Material
Bodies, Coupling Nuts, Other Metal Parts (except as noted) Brass per QQ-B-626
Contacts Male: Brass
Female: Beryllium copper, heat treated
Center Contact Plating .000030″ minimum gold
Plating (Other Metal Parts) Standard .000010″ gold or nickel plated
Insulator TFE fluorocarbon
Gaskets Silicone rubber
Crimp Ferrule Seamless copper tubing alloy
Environmental
Temperature Range – 65°C to +165°C
Thermal Shock MIL-STD-202 method 107 (test condition B) except high temperatures @ + 200°C
Vibration MIL-STD-202 method 204 (test condition D)
Shock MIL-STD-202 method 213 (test condition I). No discontinuity permitted.
Corrosion MIL-STD-202 method 101 (test condition B) 5% salt solution
Moisture Resistance MIL-STD-202 method 106, except step 7b (vibration) omitted, and high humidity measurements do not apply
Weatherproofing Crimp type: heat shrink tubing
Solder type: silicone rubber gaskets
Altitude MIL-STD-202 method 105 (test condition C), no corona at 70,000 feet.
.141″ & RG-55: 250 VRMS
.085″ & RG-122: 190 VRMS
Military Specifications
MIL-C-39012 & MIL-C-83517 SMA Specification Sheets As applicable

Note: These characteristics are typical but may not apply to all connectors.

 

Electrical
Impedance 50 Ω
Frequency Range DC-18 GHz
Insertion Loss dB maximum
For adapter 901-508 = .1v[f(GHz)] For plug 901-509 = .08v[f(GHz)]
VSWR Straight connector, .141: 1.05 + .005 f(GHz)

Straight connector, RG-55: 1.15 + .011 f (GHz)

Straight connector, RG-122: 1.15 + .02 f (GHz)

Straight connector, RG-178: 1.20 + .025 f (GHz)

Right Angle connector, .141: 1.10 + .01 f (GHz)

Right Angle connector, RG-55: 1.15 + .02 f (GHz)

Right Angle connector, RG-122: 1.15 + .03 f (GHz)

Right Angle connector, RG-178: 1.20 + .03 f (GHz)

Phase Angle Adjustment Range in Degrees For adapter 901-508 and plug 901-509 = 0° to [10 x f(GHz)]° maximum
Phase Angle Change per Revolution of Adjustment Nut in Degrees For adapter 901-508 and plug 901-509 = [0.636 x f(GHz)]°
Voltage Rating 500 VRMS peak
Mechanical
Mating Mating face dimensions compatible with the mating requirements of MIL-C-39012/55 (Type SMA)
Connector Durability 500 cycles of mating and unmating without deterioration
Material
Center Contact Beryllium copper, Gold plated
Connector Body Brass or Beryllium Copper, Gold plated
Adjusting Nuts and Locking Nuts Brass with ASTRO plate finish
Connector Coupling Nut Stainless steel, passivated
Insulation TFE
Environmental
Shock MIL-STD-202 method 213 (test condition I)
Vibration MIL-STD-202 method 204 (test condition D)
Corrosion MIL-STD-202 method 101 (test condition B)
Temperature Range – 65°C to +165°C
Military Specifications
MIL-C-39012 & MIL-C-83517 SMA Specification Sheets As applicable

Note: These characteristics are typical but may not apply to all connectors.

 

Electrical
Impedance 50 Ω
Frequency Range Semi rigid 0 – 18 GHz
Voltage Rating 375 volts peak
Dielectric Withstanding Voltage 1,000 volts rms
VSWR Straight connectors on .141″ S/R: 1.05 + .005 f (GHz)
Straight connectors on RG-174: 1.20 + .025 f (GHz)
Insertion Loss .03 v[f (GHz)] dB maximum
Insulation Resistance 5,000 MΩ
RF Leakage -60 dB minimum
Mechanical
Mating .250-36 threaded coupling
Cable Affixment Crimp or solder types
Center Conductor Solder
Cable Retention 60 – 80 lbs depending on cable
Material
Center Contact Beryllium copper, gold-plated
Crimp Ferrule Copper tubing
Other Metal Parts Non-magnetic passivated stainless steel or brass, gold or silver-plated
Insulators TFE
Gaskets Silicone rubber
Environmental
Temperature Range -65°C to +165°C
Moisture Resistance MIL-STD-202, method 106, test condition B
Corrosion MIL-STD-202, method 101, test condition B
Vibration MIL-STD-202, method 204, test condition B

Note: These characteristics are typical but may not apply to all connectors.

More Information

For more information about our products, please contact us directly at 301.838.4380 or email us at sales@shireeninc.com

RFC®, Registered trademark of Shireen Inc
LMR®, Registered trademark of Times Microwave Systems
———————————————————-

FCC notice: The marketing, sale and use of power amplifiers are governed by and subject to FCC rules & regulations under Part 15.247. Shireen’s ISM band amplifiers are available for export, military, OEM & licensed customers only. It is the responsibility of the purchaser/installer/operator to insure that only approved equipment/systems are deployed. Shireen provides full engineering support to OEMs interested in certified systems.